Just How to Replace a Tub
Just How to Replace a Tub
Blog Article
Each person maintains their personal perception when it comes to How to Install a Bathtub Yourself.
Installing a bath tub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a new one is likewise a reasonably tough task. If the old bathtub is conveniently available, the job can relocate easily; if you have to open a wall to remove the old bathtub and also position the brand-new bath tub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will need an assistant to move out the old tub and set in the new one. Make certain you have certified on your own for the work and also fit attempting it. Rather than employing a specialist to take over a halfway-completed project, it is better to think about employing one before you begin. Chances are you may need an expert plumber to make tube links.
This post will certainly assist you set up a brand-new tub in your shower room if you have actually currently purchased a new tub and don't need to change the setup of your previous water pipelines.
Your devices as well as material checklist ought to comprise the following:
Planning for the Installment
To start with, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the versatile tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing faucets can be quite troublesome as a result of the restricted accessibility that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will originate from the pipelines. When the supply pipelines have actually been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Prior to proceeding to fit the new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the needed placement. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the level as well as readjusting the feet on the bath tub till the spirit level reads level.
To install taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and also examine all joints and also brand-new pipework for leakages and also tighten them if needed. Load the bath tub as well as likewise inspect the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, repair the bathroom paneling as defined in the producer's instruction manual. Tiling and also sealing around the bathtub needs to wait up until the bathtub has actually been utilized at least when as this will resolve it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in place in between the tap as well as the sink. Secure the faucet in place with the maker offered backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap adapters. The former kind should be linked to the tap ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a stiff seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, bring about problems with wetness and possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and also are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to permit the movement experienced when the tub is in usage. The sealant can crack relatively very early if you do not take into account this movement prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader on How to Install a Bathtub, I think sharing that short article was sensible. Enjoyed reading our post? Please share it. Help somebody else check it out. Thanks a bunch for your time. Please come visit our blog back soon.
Contact Report this page